Changes

'''EQ''' stands for '''equalization''', but really it refers to '''filtering'''. '''Filters ''' can lessen or remove certain frequencies vs. others (which can be used to equalize the levels of certain frequency ranges in the signal, hence equalization). They are used to a very large extent throughout most guitar signal chains, with tone knobs, stomp pedals, amps, mixing boards, and DAW's all performing some filtering.

EQ's have a '''center ''' or '''cutoff frequency ''' that determines where on the frequency domain the change will be focused. For filters that use a center frequency, this is the frequency that will be most impacted by the filter, with neighboring frequencies also affected but to lesser degrees. For filters that use a cutoff frequency, it basically describes the frequency above or below which other frequencies are impacted. For low/high pass filters, it refers to the frequency that has -3 db of gain reduction.

Some filters have '''resonance ''' around the cutoff frequency, where a (usually) small band of frequencies actually recieve receive a gain boost. This essentially emphasizes the cutoff frequency.

'''Q factor ''' refers to the size of the range of affected frequencies. Another way to look at it is how noticeable or subtle the EQ change is in relation to the center/cutoff frequency compared to neighboring frequencies. Q is measured as 1/n octaves; a Q factor of 1 means the range of impacted frequencies is 1 octave wide. As Q increases, the size of impacted frequencies shrinks.

'''Gain ''' simply refers to the desired impact to the selected frequencies. In a band-stop/pass filter, this refers to the amount of gain boost/reduction applied to the center frequency. In a shelf filter, it refers to all frequencies past the cutoff beyond any transition band specified by Q factor. High/Low-Pass filters typically do not have a gain setting - the amount of gain reduction is determined by the distance from the cutoff frequency and the Q Factor setting.

* '''Band-Pass/Band-Stop''' - a band-pass cuts all frequencies other than the specified frequency band, essentially boosting that band in relation to the rest of the signal. A band-stop does the opposite, cutting the specified band.* '''Low/High-Pass''' - a low-pass attenuates frequencies higher than the cutoff frequency, while a high-pass attenuates those lower. The further the distance from the cutoff frequency, the greater the attenuation, usually adjustible to gradually roll off frequencies past the cutoff or blatantly remove them. Useful to remove droning lows or fizzy highs that sound noisy or inconsistent compared to the core part of the instrument's tone.* '''Low/High-Shelf''' - A shelf filter is able to boost or cut all frequencies below (low shelf) or above (high shelf) a cutoff frequency. The amount of boost or cut is consistent for all frequencies above the cutoff frequency, unlike a low/high-pass which attenuates more strongly the futher from the cutoff.* '''Parametric EQ''' - A band-pass/stop filter that allows adjustment of center frequency, Q, and gain to dial in the desired EQ change.* '''Graphic EQ''' - Several band-pass/stop filters arranged in an array of frequency bands with vertical sliders to control gain. Visually, the EQ looks like the [[Frequency Domain|frequency domain]], so the user can clearly see the impact the EQ settings will have on the signal.* '''Notch EQ''' - Provides one or more band-stop filters with variable center frequency and gain, but fixed very narrow Q. Useful to remove small "problem" frequencies from the signal.

Most amps have Bass, Mids, Treble, and Presence controls, or '''BMTP'''. The exact ranges for each control depend on the amp, and often they actually interact with each other, shifting the shape and center frequency of the others. They roughly correspond to the following frequency ranges:

* '''Bass ''' - 60 - 350 HZhZ* '''Mids ''' - 350 - 1,800 HZhZ* '''Treb ''' - 1,800 - 5,000 HZhZ* '''Pres ''' - 3,000 - 10,000 HZhZ

Some amplifiers or pedals simply use a '''tone''' control. Often this is just a band-pass filter with a wide Q, and the control shifts the center frequency. Thus, low settings allow low frequencies to pass while attenuating highs and vice versa.

Some amplifiers or pedals feature a graphic EQ with 5 or more bands, allowing greater control over the frequency response. The popular Mesa/Boogie Mark EQ uses the labels its frequencies: 80, 240, 750, 2200, 5500(although some analysis may reveal somewhat different ones in actual operation).

Sometimes, amps use switches, labeled things like "deep", "modern", "mid-shift", or "bright". These typically use EQ to alter the tone of the amp; however, there is often more to it than that, involving feedback and other non-filter based circuitry or algorithms that affect frequency response.

The way filters impact the audible tone of the guitar signal depend on their location in the signal chain, particularly in relation to distortion stages. Because most signal chains only feature one (or at least one ''main'') distortion stage, EQ is often refered to as '''pre-EQ''' if it processes the signal before that distortion stage or '''post-EQ''' if after.

| '''Fuzz ''' || Loose, flubby low-end and raucous, buzzy tone; intervals and chords sound like each note is fighting for prominence || Prominent bass and either scooped or flat mids

| '''Crunch ''' || Crisp rhythms and creamy leads; neither loose nor tight || Flat or prominent mids, low to medium bass

| '''Metal/Lead ''' || Very tight, thick bass response and searing high-end with lots of high-frequency harmonics || Prominent upper midrange and treble with low bass