8,720
edits
Changes
m
TypicallyWhen you are tracking, you want may prefer to route your physical inputs ''not'' to be routed to any physical your monitor outputs- this will minimize latency, which may assist your performance. You will route them into your DAWAlso, where you will have complete control over direct monitoring them and recording them. If need to do this to hear yourself through the monitors if you are not using your DAW software at the that moment, however. If you are reamping or recording from a player or a natural sound source, you may want to route them prefer to disable direct routing in your monitor outputsinterface, and let the DAW determine if you are monitoring the input or not. What this means is the interface software is telling the interface to patch whatever comes into ''Be careful - if you route a physical input 1 directly to outputs 1 an output '''and 2. The ''' monitor it via the DAW, the signal never has to go into from the computer where it DAW may experience have more latency before being sent back , causing the mixed signals to the interface and out the physical outputhave a comb filter.''
→Inputs/Mixer
# Guitar > Mic'ed Amp/Cab > Physical Inputs > Mixer Settings > Physical Outputs 1/2 > Monitors/Headphones
# Guitar > Instrument Physical Input > DAW > Software Return Inputs 3/4 > Mixer Settings > Physical Outputs 3/4 > Mic'ed Amp/Cab > Microphone Physical Input > DAW > Software Return Inputs 1/2 > Mixer Settings > Physical Outputs 1/2 > Monitors/Headphones
Notice how the Mixer Settings appear in the above examples - this determines how the DAW outputs (software return inputs for the interface) are routed to physical outputs. In our examples, we have the mixer set to route software returns 1/2 to physical outputs 1/2 and software return 3/4 to physical outputs 3/4.
Example 1 is a typical guitar recording setup. You are not routing the physical input directly to any output, but picking it up in the DAW where it is recorded to a track and output to the master bus, which sends it to outputs 1/2. The Mixer sees that as software return inputs 1/2 and routes that to physical outputs 1/2, which are connected to your studio monitors.
Example 3 routes the guitar directly into the interface, so that it can be recorded as a DI track in the DAW. This would allow you to reamp the track later. It is then routed back to the interface where it is sent out of physical outputs 3/4. This connects to the amp/cab, which is mic'ed and routed into the interface, which is recorded as a separate DAW track and returned to the interface and output to the studio monitors. While this method will work to record both direct guitar and the mic'ed amp/cab simultaneously, the signal is getting routed around quite a bit before finally getting to the monitors (and even the amp/cab). Thus, it may have a bit of latency that makes it difficult or awkward to play in time during tracking. A better method to record both dry and wet guitars would be to use a DI box to split the signal, sending the signal from the DI box and mic'ed cab to different inputs on the interface.
The software return inputs are what your DAW sees as outputs, so set them up accordingly. Generally, you only want to monitor the master output bus, which should be routed to outputs 1/2 in the DAW. In your interface mixer, you thus want to route software return input 1/2 to the physical outputs connected to your monitors, which are also usually 1/2. You may use Line Outs to run to other gear, or reamp via SPDIF. The best way to avoid confusion is to route each software return input to the same-name physical output. In some cases they are labeled differently, and you can order them by priority. For example, if you often use the physical Line Out outputs to run to an effects processor, you can assign them to the next open software return input, such as 3/4.
The input mixer may have additional level and pan controls. Sometimes these are linked to hardware controls on the device itself. These may not be able to prevent input clipping by lowering them - usually you need to use analog pad switches and gain knobs that attenuate the signal before hitting the A>D converters. Generally, you will leave these at max volume and center pan, manipulating such things in your DAW.
== Connecting to DAW Software ==