8,720
edits
Changes
m
no edit summary
'''I recommend locking input and output, so that it is the same for every rig.''' The only exception is where you have a more-complicated-than-usual setup and need to vary what inputs/outputs are used per rig.
{{top}}
== Signal Chain Buttons ==
Below the block buttons for each piece of the signal chain are the 3 buttons '''Stomps''', '''Stack''', and '''Effects'''. These buttons control the entire ''sections'' that encompass the blocks above them. Tapping a section button will disable/enable the entire section. Holding it will bring up its respective edit mode. Each section is covered below:
{{top}}
=== Stomps ===
By holding the "Stomps" button, you enter the Stomps edit mode, which has the useful feature of allowing you to reorder the stomps. You use the buttons above the display to move left and right to highlight a stomp, select it, then move it left and right.
{{top}}
=== Stack ===
In edit mode, the EQ block has a checkbox for pre/post operation. This determines if the EQ is applied before or after the amp block. When used as pre, it will have a greater [[Dialing_in_Distortion_Tone|impact on the distortion tone]], rather than in post, where it only controls how loud certain frequencies are vs. others, which is how amplifiers are usually designed in regards to these controls.
{{top}}
=== Effects ===
The '''Effects''' section contains 4 blocks just like the [[#Stomps|Stomps]] section; ''however'', '''Delay''' and '''Reverb''' are special - they are limited only to delay and reverb types of effects, while all other blocks are incapable of loading such effects. '''X''' and '''Mod''' function much like the Stomps, but they made have additional parameters for stereo separation that are not available when used as a Stomp.
{{top}}
== Quick Edit Knobs ==
Below the signal chain buttons are 6 '''quick edit''' knobs. These can be used to tweak parameters of the Mod, Delay, and Reverb blocks without having to hold those buttons to enter their edit modes.
{{top}}
== Type/Browse Knobs ==
Be sure not to mix these up, as it can be quite confusing. Also be sure to give good names to effects presets when you store them to be able to quickly find them, yet know what each one does.
{{top}}
== Big Knobs ==
There are also the Noise Gate and Master Volume knobs. The Noise Gate controls the [[Kemper KPA Inputs and Outputs#Noise Gate|Input block's Noise Gate]]. The Master Volume control is not part of any block and can control any of the outputs that have been ''linked'' to it [[Kemper KPA Inputs and Outputs#Link and Levels|via the Output Settings]].
{{top}}
== Rig D-Pad Buttons ==
The '''D-Pad''' arrangement of buttons on the right side is used to select rigs, or effect types/presets after turning the Type/Browse knobs to enter a browser view. The buttons can be held down to navigate more quickly. When no blocks are selected, it changes the rig that is loaded. Left/Right pick the previous/next rig, while Up/Down are like page up or page down, jumping based on the sort order. For instance, when sorted by author, up/down will jump between authors.
{{top}}
== Page Left/Right (</>) and Soft Buttons above Display ==
The '''Page''' < and > buttons move through "pages" for whatever particular block you have selected. Each page has up to 4 range-based parameters connected to the BMTP knobs and 4 checkbox parameters controlled by the soft buttons above the display.
{{top}}
== Store and Exit ==
'''Exit''' is essentially a cancel or back button. If you are editing an effect, it will exit the edit view and return to the rig overview. If you start a Store dialog and want to cancel, Exit will back out without storing.
{{top}}
== Lock ==
Locking can be engaged by pressing lock when in edit mode for the particular block. You should see a small lock icon appear on the right side of the display. When no blocks are selected, holding Lock will display all the blocks that are locked by lighting up their buttons. Tapping any button while holding Lock will lock/unlock it.
{{top}}
== Copy, Paste, Undo, and Redo Buttons ==
Effect type/settings can be copied and recalled using the '''Copy''' and '''Paste''' buttons. Sections and profiles work as well. When editing a block, press Copy, then hold another block to edit it and press Paste. If you make a mistake editing, you can press Undo, or use '''Undo/Redo''' to A/B a particular tweak.
{{top}}
== System and Rig Buttons ==
These buttons are used to access [[Kemper KPA System and Rig Settings|System (global) and Rig level settings]].
{{top}}
== Tap Tempo Button ==