8,720
edits
Changes
m
→Control Panel
== Control Panel ==
Your interface should come with software to control it, often labeled "mixer" or "control panel". This often lets you do various things with inputs and outputs similar to real-world mixing board; however, not all interfaces feature these options - in those cases, the DAW software is routing directly to the physical outputs on the unit as well as handling all monitoring and leveling. It is also where you set the sample rate, clock source, input buffer, and SPDIF source.
=== Inputs/Mixer ===
The mixer or input tab of the control panel typically resembles a mixing board. This includes the <u>physical inputs</u> on your interface as well as <u>software return inputs</u> from your DAW which your DAW will see as ''outputs''. Your DAW should automatically see all of your interface's physical inputs without having to change anything here. Different interfaces will provide your DAW software with different numbers of virtual outputs. The mixer page determines how the physical and software inputs are routed to the physical outputs on the interface. Let's look at a few examples.
# Guitar > Mic'ed Amp/Cab > Microphone Interface Mic Physical Input > DAW > Software Return Inputs 1/2 > Interface Mixer Settings > Physical Interface Outputs 1/2 > Monitors/Headphones# Guitar > Mic'ed Amp/Cab > Interface Mic Physical Inputs Input > Interface Mixer Settings > Physical Interface Outputs 1/2 > Monitors/Headphones# Guitar > Interface Instrument Physical Input > DAW > Software Return Inputs 3/4 > Interface Mixer Settings > Physical Outputs Interface Output 3/4 > Mic'ed Amp/Cab > Microphone Interface Mic Physical Input > DAW > Software Return Inputs 1/2 > Interface Mixer Settings > Physical Interface Outputs 1/2 > Monitors/Headphones
Notice how the "Interface Mixer Settings " appear in the above examples - this determines how the DAW outputs (seen as software return inputs for by the interface) are routed to the interface's physical outputs. In our examples, we have the mixer set to route software returns 1/2 to physical outputs 1/2 and software return 3/4 to physical outputs 3/4(but we only use output 3 to feed the mono guitar amp).
Example 1 is a typical guitar recording setup. You are not routing the physical input directly to any output, but picking it up in the DAW where it is recorded to a track and output to the master bus, which sends it to outputs 1/2. The Mixer sees that as software return inputs 1/2 and routes that to physical interface outputs 1/2, which are connected to your studio monitors.
Example 2 is how you would monitor your rig through your monitors without using DAW software.
Example 3 routes the guitar directly into the interface, so that it can be recorded as a DI track in the DAW. This would allow you to reamp the track later. It is then routed back to the interface where it is sent out of physical outputs 3/4. This connects to the amp/cab, which is mic'ed and routed into the interface, which is recorded as a separate DAW track and returned to the interface and output to the studio monitors(same as example 1). While this method will work to record both direct guitar and the mic'ed amp/cab simultaneously, the signal is getting routed around quite a bit before finally getting to the monitors (and even the amp/cab). Thus, it may have a bit of latency that makes it difficult or awkward to play in time during tracking. A better method to record both dry and wet guitars would be to use a DI box to split the signal, sending the signal from the DI box and mic'ed cab to different inputs on the interface.
When you are tracking, you may prefer to route your physical inputs to your monitor outputs - this will minimize latency, which may assist your performance. Also, you will need to do this to hear yourself through the monitors if you are not using DAW software at that moment. If you are mixing, reamping , or recording from a player or a natural sound source, you may prefer to disable direct routing in your interface, and let the DAW determine if you are monitoring the input or not. ''Be careful - if you route a physical input directly to an output '''and''' monitor it via the DAW, the signal from the DAW may have more latency, causing the mixed signals to have a comb filter.'' Even without latency, it would make the guitar sound louder than it should, possibly clipping the interface's output.
The software return inputs are what your DAW sees as outputs, so set them up accordingly. Generally, you only want to monitor the master output bus, which should be routed to outputs 1/2 in the DAW. In your interface mixer, you thus want to route software return input 1/2 to the physical outputs connected to your monitors, which are also usually 1/2. You may use Line Outs to run to other gear, or reamp via SPDIF. The best way to avoid confusion is to route each software return input to the same-name physical output. In some cases they are labeled differently, and you can order them by priority. For example, if you often use the physical "Line Out " outputs to run to an effects processor, you can assign them to the next open software return input, such as 3/4.
The input mixer may have additional level and pan controls. Sometimes these are linked to hardware controls on the device itself. These may not be able to prevent input clipping by lowering them - usually you need to use analog pad switches and gain knobs that attenuate the signal before hitting the A>D converters; however, some advanced devices will control analog circuitry through software. Generally, you will leave these at max volume and center pan, manipulating such things in your DAW.
There may additionally be typical mixer functions such as solo and mute buttons, which work the same way as they would on a mixing console, covered on the [[DAW Basics#SoloMixing Boards/Mute|DAW basics pageConsoles]]page.
== Outputs ==