Search results
Create the page "Wah Pedal" on this wiki! See also the search results found.
- ...such as guitar pickups. Typically connects the guitar to an amplifier or pedal and uses 1/4" male TS (Tip/Sleeve) jacks. ...itar signal in some way. These typically appear in either a ''rack'' or ''pedal'' form factor. ''Pedals'' typically have one function and are engaged or d39 KB (6,007 words) - 08:56, 18 September 2015
- ...ven to saturated distortion. Gain levels can also be augmented by a boost pedal, so high output is often completely unnecessary. And in the case of many d ...he guitar and the pre-amp. Usually these are stomp boxes, but can also be wah or volume pedals, floorboard processors, rackmount devices, etc.41 KB (7,001 words) - 22:02, 1 July 2015
- ...wide range of distortion tones as identified below, each amp or distortion pedal has a relatively similar response or signature characteristic that is diffi ...bit different than the [[Tone#Dirt, Distortion, and Fuzz Pedals|distortion pedal types listed earlier]]. Distortion pedals tend to be designed to distort o24 KB (4,066 words) - 02:44, 17 November 2015
- ...hat involves quickly footswitching pedals and/or manipulating a volume/wah pedal. You can record the part without touching the pedals at all, then re-amp i ...low and high impedance signals without distortion. However, [[Wah Pedals|wah pedals]] and older [[Distortion Effects|distortion pedals]] are typically l13 KB (2,349 words) - 01:50, 21 February 2016
- === Auto-Wah === ...ally consistent than you'd want to produce manually with a traditional wah pedal.8 KB (1,305 words) - 23:10, 7 October 2015
- ...ical pre-amp effects like distortion pedals, noise gates, compressors, and wah pedals. Or you can place it in the amp's effects loop, using it for post-e === Distortion Pedal Replacement ===16 KB (2,797 words) - 22:13, 12 February 2016
- I like to place my noise gate first in my chain (or behind the wah pedal only). I don't want any devices between the guitar and the gate from compr ...se, which is actually far lower than the noise that a saturated distortion pedal or pre-amp produces.8 KB (1,408 words) - 00:02, 12 June 2015
- ...a boost pedal. Some artists prefer to use a "cocked" (fixed position) wah pedal as a boost. ...ually uses a toe switch to toggle it on/off. Otherwise, you only have the pedal motion to manipulate the tone. Some wahs go further, incorporating feature3 KB (555 words) - 23:33, 12 April 2015
- ...effect uses barely any DSP. Just be sure to disable the default expression pedal control and manually set it to the exact setting to prevent the EQ from cli ...ne 6 Drive, Mid-Focus EQ, Parametric EQ, Tube Drive, Screamer, or even Wah Wah effects for this purpose. Other, cruder options are changing the Pod's inpu79 KB (14,365 words) - 01:31, 25 February 2016
- ...e assigned to control parameters. For example, one could use this for auto-wah. ...o follow such a path. The current effect does not sound like a real volume pedal.14 KB (2,430 words) - 23:32, 25 February 2016
- * '''Screamer''' - Classic overdrive pedal. Low drive, high output, leave the bass/treble around 50% (don't even exist ..., so if you keep that low, you won't sound like you're just using a cocked wah.17 KB (2,713 words) - 20:46, 24 February 2016
- ...p Pedals usually offer a single effect, switched on/off by stepping on the pedal (or its primary footswitch). Many players combine numerous of these effect ...alters the signal's frequency response before distortion to create a "wah wah" sound3 KB (510 words) - 23:30, 12 April 2015
- |Kemper KPA Effects#All those Wah Choices|Wah == All those Wah Choices ==19 KB (3,177 words) - 19:57, 8 March 2017
- ...mapping the pedal's anolog input to that appropriate MIDI CC # (1 for wah wah, 7 for volume, 4 for pitch, and 73 for monitor volume). ...e expression pedal, unless you like to have dedicated pedals, or have your wah/pitch with a spring in it to push it back to heel position, or do some craz43 KB (6,569 words) - 03:10, 12 March 2017