Search results

Create the page "Test" on this wiki! See also the search results found.

Choosing a Guitar

...ood if you can't play it. Unfortunately, this is not the easiest thing to test, especially in a store. '''Stores are often notorious for allowing guitars ...ing gauge and action; but it shouldn't sustain over the life of the note. Test notes on the entire fretboard - low and high frets, low and high strings.

26 KB (4,423 words) - 23:58, 21 February 2016
Choosing Pickups

My advice is to buy a few different resistors and caps and test it out using alligator clips in different series vs. parallel configuration

25 KB (4,277 words) - 00:00, 22 February 2016
Setup/Adjustments

...e of bridge). I'll raise it a bit at a time, retune at least one string to test, and see how much buzz I get playing a medium amount of pick strength acros

18 KB (3,231 words) - 15:43, 24 December 2015
Bending

...ce your finger tips get harder and less sensitive over time. It's good to test your boundaries but not to purposefully exceed to the point of injury.

13 KB (2,400 words) - 21:52, 11 June 2015
Gear Myths and Pitfalls

...erhaps hoping to fool gullible customers who don't take the time to really test their claims into believing they are improving their tone.

7 KB (1,160 words) - 23:00, 7 October 2015
DAW Basics

...noise, the wrong audio source, or silence. Rather than trying to record a test clip, then play it back; it's often simpler to disable direct monitoring on

27 KB (4,469 words) - 21:09, 20 August 2015
Equipment Checklist, Setup

* Setup and test your complete rig * Setup and Test your Rig

5 KB (756 words) - 00:04, 12 June 2015
Tone

The way you have to test this all out is by using a completely clean tone. If there's any distortio

41 KB (7,001 words) - 22:02, 1 July 2015
Reamping

* With multiple devices and adjustments to the signals involved, be sure to test each connection to be sure you are not getting any clipping and the levels * Test each connection individually as you set everything up, verifying that each

13 KB (2,349 words) - 01:50, 21 February 2016
Advanced Tuning

== Quick Chords to Test Ear Tuning ==

7 KB (1,228 words) - 01:17, 28 May 2015
Calming the Nerves

...band. You can even try to get your band small, low-pay bookings just to "test drive" some gig situations.

5 KB (880 words) - 23:05, 5 December 2015
Choosing a Modeler/FRFR

...ate "profiles" of real world rigs. The Kemper Profiling Amplifier sends a test signal to an amp and mic'ed cab and analyzes the output, creating a profile

16 KB (2,797 words) - 22:13, 12 February 2016
Noise Gate

...g. Also, make sure sustaining notes aren't outright killed. It's best to test the settings with the softest part of any song you want to play. If the pe ...Once you've found the sweet spot, move them in opposite directions. Then test to make sure Open Threshold isn't so high that it won't open for more subtl

8 KB (1,408 words) - 00:02, 12 June 2015
Sandbox

== Mono Font Test == font spacing test

6 KB (934 words) - 09:27, 31 May 2016
Line 6 Pod HD Amp/Distortion Tone

* Test guitar is EBMM JPM. Tested bridge pickup for dialing out crossover distorti Then I back down the Close Threshold. I want to test it against punchy staccatto notes and chords as well as sustaining notes. I

86 KB (15,454 words) - 23:42, 25 February 2016
Line 6 Pod HD Cab/Mic Tone

...e-sounding in my tone and went back to the drawing board, trying to really test out all the cabs in detail. The one that stuck out was the Hiway 4x12. Both ...gle it on/off and see if the tone improves with it on. If not, do the same test on Channel B. If the tone sounds muffled with no EQ, EQ on Channel A, and E

85 KB (16,112 words) - 23:47, 25 February 2016
Line 6 Pod HD Tips and Pitfalls

...et the cab to Treadplate 4x12 and the mic to the SM 57 off axis mic, and I test it through my headphones and monitors. I find this cab/mic simulation combo ...reviously thought it had a unwanted tonal impact, but I was using a flawed test.

61 KB (10,924 words) - 23:09, 25 February 2016
Line 6 Pod HD Troubleshooting

...ists, there may be a physical issue with the Pod or with the power supply. Test with another power supply if possible. If that's the issue, replace the pow #* If you are using external effects in the Pod's effects loop, you should test whether you are overloading the effects loop return A/D converter the same

33 KB (5,888 words) - 23:16, 25 February 2016
Line 6 Pod HD FAQ and Links

...ine6.com/supportarchivenew/thread/78396 Pod HD Thread on how to enter safe/test mode, firmware upgrade mode, factory reset, and calibrate pedal]

24 KB (4,153 words) - 23:27, 25 February 2016
Kemper KPA Inputs and Outputs

The same connectors are used to send and receive the test tone used during the profiling process.

20 KB (3,340 words) - 23:42, 21 February 2016