View source for Line 6 Pod HD Amp/Distortion Tone

{{Top-Level Crumbs|4}}
{{User Guide Crumbs|1}}
{{Pod HD Guide Crumbs|4}}

See also [[Dialing in Distortion Tone]].

== Distortion Types/Overview ==
{{Crumbs|blue|1
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}
See [[Dialing in Distortion Tone#Types of Distortion|Dialing in Distortion Tone - Types of Distortion]].

== Pre-EQ'ing ==
{{Crumbs|blue|2
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}
See [[Dialing_in_Distortion_Tone#Pre-EQ|Dialing in Distortion Tone - Pre-EQ]].

== Gain Staging/Layering Distortions ==
{{Crumbs|blue|3
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}
See [[Dialing_in_Distortion_Tone#Mixing_Multiple_Distortions|Dialing in Distortion Tone - Mixing Multiple Distortions]].

== High-Gain Amps ==
{{Crumbs|blue|4
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}
=== Park 75 ===

This amp delivers a classic Marshall tone. By itself, it won't get you to high-gain territory; you'll need to boost the signal (such as with an overdrive pedal, distortion effect, or simple boosted EQ) heavily to get a saturated distortion from it. I don't recommend doing that - if you want more gain but a similar tone, try the JCM-800 model instead. I like this amp for medium gain tones (AC/DC), or if I want a Marshall tone but am using a distortion pedal/effect for my main source of distortion (Satriani). Compared to the JCM-800, it has a little less distortion available but it seems to be more reactive to picking dynamics. It gives you that clean-yet-distorted crunch feel.
Cannot find image.

I like to lower the amp's Bias (and Bias X which basically "locks in" my low Bias setting). This seems to make the amp sound more like a Marshall to me - a little more nasal sounding and you can get power amp distortion without it getting too gritty or splatty. I drop it between 0 and 20%. It also allows you to dial in a bit more distortion when you want to.

This amp model seems to be one of the ones that sounds better when you crank the power section. If I'm trying to make the model distort, I'll turn Master Volume up between 85-100%, then use the Drive knob to dial in the amount of distortion. For some reason, the power section responds very "poorly" when you turn up the Presence knob on the amp. I set low, often all the way to 0%. I also keep the Bass fairly low, to keep the power amp from distorting in a muddy fashion.

If I want it to stay clean, I turn down Drive first and if I need to go cleaner also Master Volume, but I generally try to keep the Master Volume higher than 50% and turn down Drive more. The power section gets you the Marshall tone. Also, the Bias setting is more responsive the higher you set Master Volume. But keep Drive above around 5-10%. Something weird happens to the tone if you go lower.

=== Plexi Bright ===

This amp also delivers a classic Marshall tone. This model is VERY accurate. Comparing it to recordings that used this amp, it sounds almost identical. By itself, it won't get you to high-gain territory; you'll need to boost the signal (such as with an overdrive pedal, distortion effect, or simple boosted EQ) to get a saturated distortion from it, but that's not where it excels anyway. It's best for a clean-yet-distorted tone, in the vein of Randy Rhodes or early Eddie Van Halen. Compared to the JCM-800, it has less distortion available but it seems to be more reactive to picking dynamics and has a much more defined midrange.

The distortion is coming from the power section, so Bias and your EQ settings heavily affect the tone. I like to crank up presence, which gives it that real crunchy feel. Boosting treble too high makes it a little nasty. And boosting mids makes it a little too smooth for my tastes. I generally set mids and highs around the same spot, and boost presence as much or more than that. And turning up Drive all the way makes it too compressed. For the EVH tone, I like to crank the Bias.
Top of Page

=== JCM-800 ===

This amp model sounds very similar to the Park 75, but more compressed and with much more drive. Without tweaking, it doesn't sound overly Marshally; but we can get it there. Tweaked properly, it can deliver great 80's metal tones. I hesitate to call it high gain. Although it can be dialed in to produce modern metal tones, I prefer to use other amp models to do so; however, I do use it for my Megadeth patches. My favorite patches with this are for a modern Satriani tone.

Like the Park, I like to turn down the Bias and Bias X. This gives you a more natural power amp distortion and a more nasal tone.

My prefered distortion from the amp is the power amp distortion. I particularly like the sound with the Master Volume set between 65-75%. Anything more is a little too extreme; anything less just doesn't get there. I find the sweet spot, then I tweak Drive to get the exact amount of distortion/saturation I want. But don't go too high with Drive, or you'll end up mixing a heavily distorted pre-amp section with a heavily distorted power amp section, and it can sound nasty. If you need more distortion with Drive up to 40-50%, I recommend putting a boost pedal in front the amp. This will at least tweak the pre-amp distortion, so it "plays nice" with the power amp distortion.

Note that when you have a saturated distortion using the power amp section, the nature of the distortion will respond to the pre-amp EQ settings. Turning up the Bass will make the distortion muddier. Cranking the Presence will make it splatty. I like to keep those knobs conservative and cranking Mids and/or Treble. I'll often turn Bass down to like 20% and Presence to 50%, while maxing out Mids and putting Treble between 70 and 90%.

If that leaves you with an unsavory frequency response to the tone, use EQ effects after the amp to boost the bass or presence, etc.

''That said, don't try to make this amp something it isn't.'' Where this amp excels, is that rumbly, near-muddy Marshall distortion. While I generally prefer a smooth, tight low-end to my distortion, I found I wasn't impressed with the results when dialing in this amp like that. Other models simply do it better. My favorite tones from this model involve turning up the bass and not using so much gain as to make it super-saturated. I keep it percussive and buzzy, like a crunch tone from hell.

For distortion, sometimes I'll go the opposite route and turn the Master Volume down to about 35% and crank up the Drive knob. This creates a smoother distortion, but I find it has less character. I recommend using a distortion effect or EQ in front the amp, and tweaking it heavily to find your tone when dialing in the amp this way.
Top of Page

=== Uberschall ===

The Uberschall gets us into true high-gain territory. We don't need to crank power amps or use boost pedals to get a saturated distortion tone. It has a very creamy sound, which can sound great for a lead tone or some modern hard rock. But it's also a bit muddy and a little fuzzy. Without a lot of tweaking the Uberschall won't give you a tight, djenty metal tone. However, with tweaking, it sounds pretty awesome.

You can't get the distortion characteristics of this amp on any other models. The Park and Marshall models sound 80's-ish, while the Mesa, ENGL, and Elektrik sound quite modern. This sits somewhere in between. Until Line 6 adds a Soldano SLO, 5150, and/or Mesa Mark, this is probably the amp to use to get as close as possible to those tones.

Many forum members claimed that Line 6 "broke" the Uber with firmware version 1.2, because the newer version was WAY muddier. (Of course, they brought back the old Uber as the Line 6 Elektrik later on, leaving little room for complaint.) I like the changes to the tone - I think it sounds more like a real amp. But from all the clips I've heard of the real amp, I don't think it sounds like a real Uberschall. And I do not think the presence knob acts like the real thing (while the Elektrik does ironically).

You have to add a strong EQ to your signal before the tone hits the amp to get the tone where I feel it belongs. There's quite a few ways to do this. My favorite is to use a Mid-Focus EQ. You can set the high-pass frequency to around 40-60%, really dialing out the muddy low-end. With the low-pass, you can set it to 100% to keep all the searing high frequencies, or you can move it downwards making the tone more and more creamy and vowel-y. An interesting trick is to boost the low pass Q. This actually creates a resonant peak at the cutoff frequency, so you can boost the exact frequencies you want to draw out the exact distortion tone you want.

You can also use a Studio EQ, such as with Low Freq 75 HZ, -5.5db and High Freq 800/1500 HZ, +6 db. I found good results from doubling up two Studio EQ's, so you can fine-tune the punch and mids frequencies too, to keep the tone thick while keeping it mud-free. Or you can just use a Parametric EQ to boost the center frequency you want. Or use combinations of EQ's. I like using a Mid-Focus to trim the mud and grit, and use a Parametric EQ to boost the upper mids/treble with the perfect Q.

You can alternatively use a Tube Screamer and turn down Bass while cranking Tone, but leave Treble around 50% (for the Classic Distortion, turn up Filter to around 70-75% and turn up treble just a bit).

The EQ controls behave a little strangely. Mids seems to also affect the highs - I like to turn it up high and use EQ effects to really dial in the midrange response I want - usually I'll cut around 750 HZ a bit. Treble gives you good control over dialing in just the right amount of sizzle on top. Presence behaves more like a traditional presence control than the midrange-peak sweep on the actual amp, but watch out because strong settings will strongly affect the tone.

I tend to leave the DEP's alone or near 50%, with the exception of Bias X. I used to adjust Hum to about 70% which seemed to change the tone a little, but then I noticed there's this faint digital sounding tone in additional to the main guitar tone - it's most audible when doing slow bends on the higher strings. So I now leave it closer to 50%; however, you have more wiggle room as long as you keep Master around or lower than 50%. Bias X I like to turn up, which gives notes more of a blooming type sound and makes the amp more expressive. However, too much makes the tone sound a bit fake. I usually settle around 65-70%. If anything I'll reduce Sag a bit, but this will make the tone less djenty and more percussive. Bias can change the mid-range response heavily and make the tone a little more gritty at higher settings. The Master DEP alone doesn't seem to have a very strong effect on the tone, other than compressing the tone at higher settings. But in combination with the other DEP's, it acts to amplify or diminish their effect. So I treat it like a compressor, which comes in handy for tones where you don't want a heavily-saturated distortion, but you want good sustain. However, I balance the other DEP's against it, keeping them more conservative if I boost this. For a super smooth tone, I find 40-45% is good. Anything lower starts to lose tone. Anything higher introduces a bit of roughness.

=== Dual Rectifier ===

Line 6 dialed in the classic Mesa/Boogie Dual Rectifier tone beautifully. You can get a variety of great tones from it, from hard rock to metal. It will djent without a boost, and it doesn't have any awkward kinks that you have to dial out. I don't necessarily try to replicate an artist's rig when I'm trying to dial in their tone - I often find a different amp model dialed in a clever way gets me closer to the tone. This is not the case here. If I want to replicate an artist that uses a Boogie Rectifier, I use this amp model without hesitation. If you like its tone, you lucked out with Line6's implementation. I use this amp for modern Dream Theater and Meshuggah tones, as well as some of my own personal tones.

I find this is the most straight-forward high-gain amp on the Pod HD. All the controls behave as you'd expect them to. The only surprise is that it has loads of bass. When matched with the rather bright Treadplate cab; however, it gets canceled out and sounds great. The only thing to watch out for is the treble knob; it can dominate your tone at higher levels.

You probably don't need to use any form of overdrive/EQ before the amp - it is preset to djent. However, a mild EQ will dial out any mud if you have dark pickups. Also, a slight EQ boost at 1 kHZ will make it slightly more djenty. Using a Tube Screamer will make the tone super tight, which works great for the down-tuned metalcore or death metal stuff.

This thing has tons of bass in comparison to other models, and it is difficult to tame. I find a Parametric EQ with frequency around 15% works best, and I usually use that in conjunction with a Mid-Focus EQ - I'll set the high pass Q to 0% and move HP Freq from 0% upward until I find where the boominess is gone.

The most control over the distortion tone comes from the Master Volume parameter. Higher settings get a dirtier distortion - a lot more bite. I tend to set it lower - around 30%. This keeps the tone nice and spongy but still with a good bit of bite. I'm still experimenting with the rest of the DEP's, but if anything I'll just set Sag lower. I like the Bias controls usually at 50% for now. To get the super-cold sounding Meshuggah tone, I change it up a little - I like Master Volume pretty high (~80%). Hum seems to change the splatty-ness of the distortion. I believe I turn it down a little sometimes to make the tone more spongy.

=== Fireball ===

A great representation of the ENGL sound - very midsy yet modern and djenty. It's a bit looser than the Dual Rectifier and a bit dirtier - it has a wonderful gritty tone, think Jeff Loomis. Has loads of distortion and is pretty simple to dial in. It's a great choice for any kind of modern metal when you don't want the Dual Rectifier sound. I use this amp mainly for Periphery and Scar Symmetry tones, but you can actually get a good 80's metal sound out of it due to its midrange response.

The Presence and Treble controls are a bit sensitive at higher settings, but sometimes you need them up high to get enough sizzle to the tone. They seem to provide very subtle changes during initial adjustments than start to hurt the tone, usually making it too harsh. Bass doesn't seem to do very much. Mids is more responsive but also more forgiving - I usually set it up fairly high and, like the Uber, use EQ effects to really dial in the midrange response.

A mids-boost on this amp can make it really djenty. Ola's hand job patch uses a Screamer with Bass down to 35%, tone up to 75%, and Treble at 45%. I also like using a Classic Distortion with Drive ~5-15%, Bass 35%, Filter 75%, Treble 60-65% to make it really aggressive - djenty but also dirty.

Another trick is to use EQ before the amp, boosting the mids, but turning down some of the really high end. This makes the tone much smoother sounding - Studio EQ with Low Freq at 700 HZ, +5 db, High Freq at 5000 HZ -4db.

I generally like to turn up the Master Volume to the 70-100% range for my Vai tone. This really makes the amp thump, but it also makes it a little looser. If you want a tighter tone, turn it down. This amp seems the most forgiving with its DEP's. For lower Master Volume settings, reducing Bias tends to make the amp sound more real in my mind, although this does suck out some mids which you'll have to add back in. For higher Master Volume settings, Bias tends to make the amp sound a little looser and more midsy and warm at lower settings, but tighter and crisper and colder at higher settings. For the life of me, I can't seem to notice any change in the tone with the Hum control.

=== Elektrik ===

I'm meh on this model. It doesn't do anything the Uber doesn't do that I find the Uber does better, even if it takes more tweaking with the Uber to get there. I never use this amp. It sounds too much like a modeled amp, not a real amp to me. You can hear it in the mids. It sounds like some annoying kid going "uhh uhh uhhh".

Immediately selecting this amp, you will notice something doesn't sound right. For some reason, the default "Master Volume" DEP value is 100%!!!! Set that down to at least 50% or lower, and this amp becomes at least usuable.

The Presence setting is a little non-traditional. I find a value around 45% keeps the amp djenty. Higher values make the amp more crunchy like a Marshall. Otherwise, it behaves similarly to the Uber, especially the mids knob.

=== Dual Rectifier "Pre" ===

Normally I don't deal with the pre-amp only models because I feel like they're the same as their full counterparts, only missing bite and a full frequency response (they sound thin). Yet the Dual Rectifier's pre-amp sounds different from the full model - I consider it an entirely different amp model. It has a very smooth, spongy distortion, compared to the full model having more bite and grit. I like to use it for my Metallica black album tone.

You'll notice with the "Pre" variant, you have to use a bit more gain. Also, there's much less bass and more mids. So I generally turn down Mids and turn up Bass more than usual.

Otherwise the same rules apply as the full model, regarding boosts and EQ's. There are no DEP's to deal with.

=== SLO Overdrive ===

This is easily one of the best models on the unit. It sings quality, especially in its rich midrange response. It has plenty of punch and warmth, so it never sounds thin like the Treadplate and Fball models. While the high-end is there and can be quite ronchy, it is never overbearing or harsh. But the real spectacle is the signal-to-noise ratio. This model has very little noise compared to the other models, making direct comparisons to them sound like a generational leap - like SD to HD.

The overall tone is probably somewhere between a Marshall and the Fireball. It doesn't feel quite "modern" enough for chugga chug downtuned metal, but it's certainly not vintage. It makes for a sweet 80's - 90's hard rock tone and will even work as a thrash tone. I find it does wonders for Vai tones.

One thing about this amp reminds me a lot of the Plexi model actually. It's got that nasal breakup to the pick attack that adds character to the tone. And as hard as I've tried, I could not dial that out. Which is good and bad - for some tones I like it, but it doesn't work for a sweet, super-smooth, high-gain lead tone. If you want the SLO tone without that nasal attack, try to boost the SLO Crunch - it's "cleaner" in this regard, but as you might expect, less saturated and more crunchy.

The natural tone of this amp has a bit too much low-end breakup to me, and doesn't sound focused enough. I like to put a Distortion pedal or some EQ in front of it to give it a bit of a mids-boost. Nothing too fancy or extreme - it doesn't need radical treatment to draw out the sweetness. I don't find the amp is very versatile. Extreme settings are more likely to sound ugly than interesting.

Another interesting point to this amp is that the EQ knobs are not as drastic as one might expect. I find I use them more to change distortion tone than to really EQ the tone. In that sense, they are similar to the Fball model. If I want more low-end or high-end, I'll use EQ effects after the amp. I usually keep the amp's EQ knobs a little over 50%, but find boosting mids higher can sweeten up the sound.

I have not had much success tweaking the DEP's. I find they sound best around 50%. Boosting Master can have some effect on the midrange - sometimes I move this up to around 60-65%. But beyond that the power amp distortion is too broken up for my tastes. As usual, Sag works as expected and can be set to taste. Hum gets swirly and ugly if turned up yet reduces the richness of the distortion if turned down. Bias almost acts like a mids control.

=== Doom ===

The Doom basically sounds like a heavily customized Marshall; and as you might guess from the name, it is dialed in towards doom, sludge, and black metal tones. It's kind of vintage and droning, but at the same time it stays focused and doesn't get a little weird like a Marshall would if pushed that hard. Personally, I don't really mess around with these tones, so I can't speak a lot on how to dial it in.

One thing that has been mentioned about this amp model is that it takes Distortion pedals very well. You can set the amp to provide a mild breakup, then drive it hard with a heavily distorted pedal. Or you can use a pedal with a slight breakup and drive the amp hard. Either way you get a usable tone without much tweaking. And this works across a wide variety of the distortion effects available on the Pod. So this will be my focus for the amp. I'm hoping it might deliver a better tone for some of the patches where I use a heavy pedal distortion into a slightly broken up Marshall, like my Satriani and Opeth tones.

=== Epic ===

This amp requires heavy tweaking to get it in the "usable" range for me. But once there, it provides a tone no other model delivers. I would describe it as dry, thrashy, tight, and not-too-saturated. I think it should sound good for thrashy death metal tones like Opeth, Extol, or The Faceless.

If you try to get pre-amp distortion from this model, bring your broom. It's a mess. Rather than try to use EQ or boost pedal trickery to clean it up, let me save you some time. Don't bother. It sounds like a broken amp. Set Drive to 5% and forget about it. All the distortion is going to come from the power section. Crank the Master DEP to 100%.

I find a distortion pedal is necessary to focus the tone. Also, the amp's EQ plays heavily into the distortion tone you get from its power section. This is a bit tricky. While I like to boost mids in my pre-eq or distortion pedal, I find turning up mids (or even using 50% mids) can consume the tone, causing it to sound too dark and compressed, like a pedal distortion. I like to back off of it, even going down to like 15% to get more of a natural bite out of the tone. On the other hand, I boost Treble, and keep Presence slightly under 50%. Of course, these relationships change depending on how you pre-eq the amp. Be warned.

As for DEP's, again Master at 100% - it's the source of the distortion. I suppose you could turn this down if you wanted to use a pedal for your distortion, but this amp has so many pitfalls, I'd be scared to try to dial that in. Sag can be set to taste, but I find the amp is still tight and percussive at 50% and sounds more natural than if you set it any lower. Hum I actually turn down a little. With Master cranked, the amp can easily get into "broken power amp" tones, swirling and such. Turning down Hum a little helps prevent this, along with smart EQ settings and amounts of gain. Bias I turn down a little - this makes the tone have a bit more bite, but going too low makes it sound thin and scooped. Bias X I turn down all the way. I don't like what turning this up at all does to the tone - seems to make it sound flat and overly compressed.
Top of Page

== FW 2.6 Metal Pack Amps ==
{{Crumbs|blue|5
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}
=== Panama ===

=== Brit 2204 ===

=== Mahadeva ===

== Distortion Effects ==
{{Crumbs|blue|6
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

My favorites here are the [[#Line 6 Drive|Line 6 Drive]], [[#Tube Drive|Tube Drive]], and [[#Screamer|Screamer]]. The Line 6 Drive seems the most versatile due to how it uses the mids parameter. It also has a natural distortion tone. I liken it most to a Boss DS-1. The Tube Drive also has a natural tone, and it is great for warming up an amp - I think of it as adding an extra tube gain stage to the amp. Its distortion tone is a bit vintage-sounding, yet I usually use it to make a vintage-sounding amp model more modern sounding. The Screamer has its classic tone, which seems to be a be a bit colder and tighter than the other options.

=== Tube Drive ===

This is probably my most commonly-used distortion Effect. It works well as a filter. It tends to make the tone a bit warmer and smoother. It also works well as a primary distortion, getting the kind of tone I'd expect from a Boss DS-1 or a general-purpose distortion pedal that uses a tube for distortion tone.
Cannot find image.

I use this frequently with the Marshall amps. It helps give them a bit more lower midsy warmth without losing bite. I find it can add a touch of compression, so you can preserve the distorted-yet-clean Marshall crunch while still having a thick lead tone and nice sustain. I use it in front of the Fireball to get a less djenty sound, while still still keeping the crisp high-gain tone from the amp.

I use this in my early Van Halen, Slash, Rhoads, Vai, Satriani tones. I even use it for a Meshuggah tone. I use it in various other patches when I need a solid distortion effect.

I avoid turning the Treble knob too high here. Bass I often turn up fairly high, and I'll set mids even higher sometimes. But Treble can make the tone a bit harsh when cranked up.

=== Screamer ===

The Tube Screamer is one of the most infamous pedals of all time. Used by Stevie Ray Vaughn to God Forbid, it's a classic choice for enhancing an amp's distortion. I don't find myself ever using it as a standalone distortion, as it comes off a bit thin and harsh. But using mild Drive levels and pre-EQ'ing amps has a unique effect that is difficult to describe.
Cannot find image.

''The first thing you need to realize is that the "auto" impedance setting when this effect is first in the chain is 230 K.'' This may leave the sound a little less crisp than desirable - the actual pedal's impedance is 500 K. Try setting the input impedance manually to 1 M to get more bite in the tone. Conversely, if it's not the first effect in the chain, or you aren't using "auto" impedance, it might have too much bite for your tastes, and you might want to consider reducing your input impedance to 230 K. My suggestion is to use 1 M then use an EQ effect to roll off a little high-end before the pedal for the most authentic tone.

This pedal tends to reduce bass and focus in on mids and presence, pushing your amp into djent-mode, without necessary making it gritty. It can make the tone pretty cold as well, which works nicely for metal.

The Pod HD version includes bass and treble controls not on the original. Use them where tone isn't getting your tone where you want. I find I'll often turn up bass a little bit, as this pedal really sucks out a lot of bass.

This pedal dials in a good bit of upper mids, but it also seems to roll off some top-end (in addition to the "auto" 230 K impedance) and can flatten out your attack some. Take this into account when setting Amp DEP's and compression.

When dialing in this pedal for metal, the pitfall is to set Tone very high. This definitely gets the cold, presence-focused, brutal tone the pedal is known for, but it can be a bit too much and make the tone too "scratchy". If you get to that point, try backing off the Tone.

=== Classic Distortion ===

The Classic Distortion seems at first to be inferior to the two distortions mentioned above, and maybe it is; but it's worth considering when you need a bit of something different that you can't find with the two above. Its standalone distortion tone is similar to the Tube Drive. But its filtering can be similar to the Screamer.

The trick to reigning in this pedal is to keep things relatively neutral. The bass and treble parameters can be quite extreme. From there, it's all about finding the sweet spot on the Filter control. This parameter is very tricky - turning it up seems to brighten the tone and scoop it simultaneously. I find I usually stay around 50% and often go lower with it, rather than higher.

One thing I like about this effect is that it gets pretty much 100% clean at 0% Drive. This can make it more ideal than the Screamer, which cannot get as clean, for certain scenarios where you want the Screamer filter tone, but you don't want the scratchy high-end, like a soft lead tone.

=== Overdrive ===

This is basically a fuzzier version of the Tube Drive. The break-up is looser and a bit more raucous. I don't really have any purpose where I use this as a filter, but I do use it as a standalone distortion for a fuzz tone. I find I have to give it a little pre-EQ bass boost to get it as dark and fuzzy as I want it. I don't really have anything else to say about it.

=== Facial Fuzz ===

I'm not really into fuzz tones, but I do use this occasionally, particularly for a Hendrix or Eric Johnson tone. I find the key is to mix it with some Marshall amp distortion and give it medium gain. It mostly affects the break-up and looseness of the feel to your playing, while the amp distortion provides the real distortion flavor. I don't find it does much when used solely as a filter, and it's too crazy for my tastes when used as a standalone distortion. I also perform some EQ after the distortion to trim off some of the nasty low and high-end this thing produces, otherwise I get a muddy and gritty amp tone.

=== Line 6 Distortion ===

This is the best distortion effect for standalone, high-gain distortion. I use it to simulate 90's Randall amp tones - it has that solid-state kind of tone where it seems unnaturally responsive and crunchy with no flub. I do like to pre-EQ it to add a little more midsy crunch and djent to it.

The difficult thing is finding a good amp to pair this with. I've had good results with some of the Marshalls, but you have to give them a little pre-amp Drive or the tone is weird - it almost gets a little fuzzy like the amp is struggling to work properly. Other good options are the Fender Blackfaces or the Divided by 13. The main thing to watch out for is excessive bass and treble. It's almost best to start with mids at 100% and everything else at 0% and work towards a natural-sounding tone. You're likely only going to be able to get so far, then use EQ effects to really shape things into a natural tone.

=== Line 6 Drive ===

This may actually be the best distortion effect in the Pod. Its Mids parameter varies the type of distortion you get, so as you go from 0%-100% you go far from farty to almost fake-sounding tight djentiness. I don't go too far off 50%, but there's so much ability to dial this in, I don't need to. Once you find your Mids spot, then use Bass and Treble to dial it completely in.

I sometimes like to run a Mid-Focus EQ before or after this distortion to trim some of the ultra high-end if I'm trying to get a super bright distortion, because it can make it too bright in the very high frequencies, which tend to make amps create a grittier tone with a more broken up attack. With more conservative settings, it's not (or less) necessary, but is something to keep in mind.

I mostly use it as a filter (0% Drive), but it seems like I get the best tone when I attenuate my signal before this effect with a Volume effect, to make sure it's not distorting or even compressing at all. It does work well as a standalone (high Drive) distortion, and I also occasionally use it to add a slight bit of distortion and run it into amp distortion to get a nastier tone with a little buzz.

=== Others ===

I find the others sound fake or just crazy. They'd be good for a kind of out-of-control intro tone, but I don't really mess with that very much.

The Heavy Distortion is supposed to be modeled after a Boss Metal Zone; but without the adjustable mid-frequency, it is nowhere near as versatile. I find I prefer to use the Line 6 Drive (which does have the adjustable mids contour) or Line 6 Distortion (which is more dialed in where you'd kind of want it) where I would use this.

The Jumbo Fuzz is supposed to give you a Zepplin tone, but I haven't tried it yet. The Fuzz Pi is all over the place, which I haven't found a use for - maybe Nirvana? The Jet Fuzz is a phaser + distortion - I think I'd prefer to keep those separate. Same with the Octave Fuzz - I'd rather use separate effects and have more control over each.

The Buzzsaw and Color Drive seem to just add some dirt into the tone - definitely not my thing.

== Power Amp D.E.P.'s ==
{{Crumbs|blue|7
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

The best approach to these is to treat them like you would on a real amp. You'd likely spend most of your time finding the sweet spot for the master volume. Next you'd likely tweak the bias. Sag, hum, and bias excursion would be more complicated modifications to the amp that probably won't help the tone, other than the slight variation in such parameters you'd get from using different tubes.

=== Master ===

This controls the amount of power amp compression/distortion, similar to the master volume knob on a real amplifier. This setting affects how much the other DEP settings affect the tone - they are colors of power amp compression/distortion. Setting this to lower settings (even all the way to 0%) approximates the tone of the pre-amp only models. This is helpful to dial in a sweet spot between the default "pre" and "full" amp models. It is also useful to dial out unwanted power amp distortion on cleaner models.

For the high-gain models, the default 50% sounds about where I like it. I may tweak a little this way or that way to make the tone a little edgier or smoother, but I generally don't go far. The Treadplate becomes rather harsh at higher settings, while the Fireball and Uber tend to compress and get a little more life in the midrange, at the expense of high-end richness and smoothness. I like to turn up the power section to around 65% on the J-800 usually, which offers a more aggressive distortion than its preamp.

=== Sag ===

Controls the amount of power amp sag, which is a dip in voltage over a sustained load. I find it mainly causes a slower attack and a chunkier bottom end. See [http://en.wikipedia.org/wiki/Distortion_%28music%29#Power_supply_.22sag.22 this wikipedia entry]. Lower settings offer more of a dynamic attack and tighter feel, but can change the tone.

In general I leave this alone until I've made almost all my other tweaks. I'll use it to add more/less attack to the tone. I usually stay within 40-60%. Lower settings can make the tone a bit edgier bit thinner. If I want to thicken the tone up, I usually add Decay in the Cab DEP's to do so. But sometimes, I like to turn up both Sag and Decay to get it extra thick.

Some distortion effects introduce their own kind of sag to the tone, so you actually want to reduce the Sag DEP to compensate. Too much sag or thickness to a tone can make it sound artificial - like a solid state pedal that claims to give you teh brootz tonez. But not enough Sag and your palm mutes will sound more like an overdriven clean-channel crunch tone than a thick djent tone.
Cannot find image.

=== Hum ===

This controls the AC ripple plate voltage, which affects how the power tubes behave. For some amp models, this control has little effect; for others, it can be dramatic. It's hard to describe, and it varies from amp to amp. Also, the changes in tone are not completely linear. IE - if you find it to sound warm at 50% and cold at 25%, it's not necessarily going to sound really cold at 0% or really hot at 100%. ''Be warned: this control can cause weird things to happen to your tone when you move it off 50%.'' For instance, I liked the tone when I turned it up from 50 to 70% on the Uber model but noticed it introduced a faint, kind of digital-sounding ghost signal doubling my guitar parts. I almost always leave this control at 50%.

The big exception is the Uber model. I find a touch more Hum (55-60%) changes the distortion to thicken it up a little and make the overall tone a bit darker, which I really like. I also find setting it around 75% gives me a more evil tone, which I use to approximate a 5150. I have not had such luck manipulating this control on other amp models.

If you do choose to boost this, pay attention to your Master DEP setting. You will have to balance the two or you'll end up with a tone that hums and swirls and sounds like an out-of-tune radio. You can tell you've got too far when this control noticeably increases the amount of humming when you're not playing (provided you don't have a noise gate that is muting it).

=== Bias ===

Determines the bias of the power tubes. Lower settings resemble class AB operation where you have more headroom and where you do get clipping, it is more natural sounding. Higher settings resemble class A operation, which is often said to sound warmer (more mids/presence) but can get grittier-sounding clipping.

I recommend playing with this control from 0 to 100% for your patches. It can cause subtle frequency response changes to the tone that you can't get using EQ. It seems to improve the signal-to-noise ratio for certain frequencies. It can also change your distortion tone. While I generally end up around 50%, I'm usually slightly one way or the other. In some cases, I'll have this at 100% while others at 25%.

For some of the more vintage amp models that exhibit crossover distortion, turning this up can reduce or eliminate the crossover distortion; however, it will have a significant impact on tone. I prefer to reduce the Master DEP and boost Bias X.

=== Bias X ===

Controls bias excursion or how far the bias can deviate from its setting under different loads. I find this has the most effect on cleaner tones where the attack of the signal can be a spike exponentially larger than the sustained note - I've found higher settings clean up attack without sacrificing tone, acting like a compressor/limiter. Also useful to "lock-in" a bias setting by turning it down when you're getting power amp distortion. Or you can get some "bloom" to notes by turning it up.

Bias excursion seems to operate in phases. When a load is first applied (ie, when playing a note), the voltage overloads the tube, and the tube biases away from its normal setting. It then hits a point where it begins to recover and return to its natural bias. I assume this is why I feel like boosting this parameter can add "bloom" to a sustained note.

I most often leave this alone, or turn it up to get the vowel-y bloom effect I just mentioned. Just be careful. While at first it can generate some compression and a slight change in the distortion character, which as this transitions over time gets the "bloom" effect, going too far can make the entire tone change, in a way I feel is bad. Certain frequencies are not reproduced well, and the tone seems more noisy and dull. I find I like 65-70% and that's with a power section not being pushed very hard. The most I'll ever do is 80%, and that's when I've got the Master DEP set low, like 20%. Beyond that is the tone graveyard.
Top of Page

== Dual Amps ==
{{Crumbs|blue|8
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

The Pod HD allows dual amps; however, I tend to avoid this, other than for [[Line_6_Pod_HD_Cab/Mic_Tone#Dual_Cabs_2|dual cab]] purposes, which this section isn't referring to. I just don't like the way it sounds, especially for high gain. However, there are a couple ways to make it sound good, which I'll cover below. ''Additionally, it will eat up your DSP usage, putting strong limits on the amount and type of effects that you can use.''

I first started experimenting with dual amps on the Pod X3. I figured if I like two different amps, mixing them together would sound great. Wrong! ''It felt like the amps were fighting each other, creating a noisy mush.'' To get them to clean up, I would have to pan one left and one right. This is one way to get a good sound from dual amps, but the problem is that you have to run this tone in stereo. If you want to record, you can't double track by panning one track hard right and the other hard left, which is what I like to do. You may think you can just record one stereo track with the two different amps already panned in the Pod, and this will sound just as good as if you recorded each amp as a mono track and panned them in your recording unit; but from my experience, ''it always sounds better to actually record two mono tracks.''

The main way I could dial in a dual amp tone the way I liked was to ''basically crossfade their frequency responses''. So I'd cut certain frequencies to the point where you couldn't hear them at all on amp A, then boost those frequencies so that they were the only ones you'd hear on B. In other words I'd mix the bottom end of one amp with the high end of another amp. Or I'd cut the mids out of one amp and dial in only mids on the other. I don't see this so much as mixing two amp tones as much as creating a single amp tone with parts of two different amps. IE - FrankenAmp.

Another way is to ''use different gain levels on the amps''. So one amp would have close to or full saturation, while the other would be medium or low gain, providing just a touch of crunch. This can get you that distorted yet clean/crunchy tone.

In any case, I don't use dual amp tones, because I feel there is no significant tonal improvement, they take longer to dial in, and they limit the amount of effects you can run.

There is one exception to this rule, which is if your second amp is actually "amp disabled". ''This uses no DSP whatsoever. And it'll give you a clean tone, which you can use to reinforce your distorted tone.'' You want to pan both mixer channels to center and set the clean tone so it is just barely audible. You want it to really just add a little attack because a heavily distorted tone can lose some attack. Most of the time, I don't use this setup; however, because it is difficult to get right and I don't find it really delivers a much better tone. It's easier to screw up than get right. If you do use this approach, ''try adding some compression and EQ'' to the channel with no amp; so you don't get too much attack or bright clean tone.

== "Full" vs. "Pre" ==
{{Crumbs|blue|9
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

You'll notice there are two versions of every amp on the Pod HD, one with the amp name, and one with the amp name plus "pre". The "pre" amps only model the pre-amp section of that amp. They were designed to be used in combination with the Line6 DT-50 line of amps, which have switchable power sections/modes. Of course, most of us don't have DT-50's.

People on the forums have argued a lot about which versions you "should" use for any particular setup. For instance, I've often seen posts saying that if you are running the Pod to a real amp, you should use the "pre" version, because otherwise you're getting the power amp emulation plus power amp distortion from your real amp. Likewise, if you run "direct", you "should" use the "full" model, otherwise you're not getting any power amp in the sound. They argue that you want one power amp coloration, not zero or two.
Cannot find image.

This is logical, yet I disagree nonetheless. The power amp emulation has a rather profound effect on the way the Pod's amp models sound, even if you turn down the "Master Volume" DEP or set the bias colder. Your real amp is unlikely to replicate how that amp model's power section sounds on the Pod. You might not be cranking your amp to the point where it's getting power amp distortion, even at gig levels - many power sections are designed to have lots of headroom and remain transparent. And even if your amp's power section does get pushed into overdrive, it may still sound good with the "full" model on the Pod. Just because you're running two power amp colorations doesn't mean it will necessarily sound worse.

On the other hand, there is a certain crispness in the "pre" models that seems to be lost in the "full" models, even with the Master DEP at 0%. Even if the frequency response is not ideal, it can be tweaked to where you want it with amp EQ or EQ effects.

Thus, in general I prefer to use the "full" models for "direct" tones, while I'm about 50/50 on which to use for "live" uses - it depends on the patch.

Keep in mind that if you have a power amp that easily distorts, it is more likely to sound better with the "pre"s than the "full"s. I encourage you to experiment to determine what suits you best. On the other hand, some tones rely on power amp distortion. If your power amp isn't providing the same breakup, you will have to use the "full" model or won't be able to achieve the desired tone, even if you crank your real amp.

Finally, if your real power amp does distort at volume levels you will be playing at, take note to make patches that distort it in a desirable way. As noted [[Dialing_in_Distortion_Tone|on the Dialing in Distortion page]], the EQ of the tone you send to your amp will greatly affect the way it breaks up. If you use too much bass, the power amp distortion may make the tone muddier than you like. Your gear is limiting you. You'll have to brighten up your patches to compensate or get new gear or play at lower volumes.

== The Elusive Pure Clean Tone ==
{{Crumbs|blue|11
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

The PodHD doesn't offer any pure clean amp models (yet? as of 7/18 there is a Soldano SLO Clean model available for the 300/400 that may fit this bill), like a Roland Jazz Chorus. This doesn't mean getting a pure clean tone is impossible though.
Cannot find image.

''If you are not using Input 2: Variax (null), I suggest you start with that adjustment.'' One of its benefits is a lower signal level, which allows clean tones to instantly be a little cleaner. But there are [[Line_6_Pod_HD_Setup#Input_2|other benefits]].

The cleanest amp model is the Blackface Dbl, based on a blackface Fender Twin Reverb. Line 6 modeled it in "warts-and-all" fashion, meaning it can get a little nasty sounding when running modern high-output humbucker pickups into it, rather than the 60's era single-coil pickups it was designed for. Still, there are a number of ways to tame it. Here's a list, ordered by what I prefer to preserve tone, which applies to getting a cleaner tone in general on all the amps.

* Change input settings - input 1:guitar, input:2 variax
* Put a Studio EQ in front the amp, and set gain to -X db.
* Use no amp model, using compressors and EQ effects to simulate one
* Try turning up bias or bias X
* Try turning down Master Volume
* Use a Parametric EQ to find which frequencies really push the amp to nasty breakup, then reduce those frequencies (you can dial them back in after the amp)
* Use pre-amp models instead of full models
* Change input impedance - lower values will be softer, darker, and looser but less likely to distort

My favorite tone from the amp comes from a dual amp tone combining the Blackface Dbl on one channel with no amp on the other. I use a compressor and some EQ on the "no amp" channel. Then just set the volume so that they complement each other. You get the shimmering clean sound of a compressed and EQ'ed raw guitar signal mixed with the warmth of the Fender clean.

I also did a little experiment to see how much power amp (crossover) distortion I could dial out of the Blackface Dbl without causing it to lose its desirable tonal nuances. You might still get a little distortion using the advice below, but the idea was to preserve tone more than completely dial out distortion. All starting values are the exact default settings when you select the amp.

* Default Master Volume is 100%. Change that to 20%.
* I found changing the Bias changed the tone too much. I was able to get good results from Bias X, though. I set it to 80% and that helped clean it up a little. I assume this means that the bias is changing to a colder setting when it would be pushed hard enough to exhibit the crossover distortion, but not for any notes softer than that. I changed Bias X from 50% to 80%.
* Turn Drive from 37% to 60%.
* It seems like this may change the dynamics just a little bit. I tried adding a Tube Comp before the amp. I set Level to 0% and Threshold to 95%. I think I prefer the tone without the Tube Comp - you may want to try it though.

Some general notes:

* For my setup, I put amp/channel volume at 50%. Any higher than this and I'd clip my DAW input. But I run via SPDIF and I think I boost the SPDIF output level. So you might be able to go higher.
* My mixer has channel 1 panned full left and channel 2 panned full right. Levels for both channels are 0 db.
* My input impedance is on auto. My input settings are input 1: guitar, input 2: same. Pad switch is turned off.
* Test guitar is EBMM JPM. Tested bridge pickup for dialing out crossover distortion by strumming as hard as I can. Tested tone using single notes and chords all over the neck for bridge, neck, and coil-tapped bridge+neck pickups.

== Noise Gates ==
{{Crumbs|blue|12
|Line 6 Pod HD Amp/Distortion Tone#Distortion Types/Overview|Dist Types
|Line 6 Pod HD Amp/Distortion Tone#Pre-EQ'ing|Pre-EQ
|Line 6 Pod HD Amp/Distortion Tone#Gain Staging/Layering Distortions|Gain Stg/Layering
|Line 6 Pod HD Amp/Distortion Tone#High-Gain Amps|Amps
|Line 6 Pod HD Amp/Distortion Tone#FW 2.6 Metal Pack Amps|Metal Pack
|Line 6 Pod HD Amp/Distortion Tone#Distortion Effects|Dist FX
|Line 6 Pod HD Amp/Distortion Tone#Power Amp D.E.P.'s|Amp DEPs
|Line 6 Pod HD Amp/Distortion Tone#Dual Amps|Dual Amps
|Line 6 Pod HD Amp/Distortion Tone#"Full" vs. "Pre"|Full/Pre
|Line 6 Pod HD Amp/Distortion Tone#The Elusive Pure Clean Tone|Cleans
|Line 6 Pod HD Amp/Distortion Tone#Noise Gates|Gates
}}

For general advice, see [[Noise Gate]].  Notes below apply strictly to the Pod HD's gate offerings.

=== Noise Gate vs. Hard Gate ===

There are two noise suppressors on the Pod HD, the standard "Noise Gate" and the more advanced "Hard Gate". In general I prefer the Hard Gate, because its a true gate. The Noise Gate is part gate, part signal processor and can result in "tone suck". At higher settings, it tends to make the tone sound thinner.

The Noise Gate uses less DSP than the Hard Gate; however, so sometimes it's the Noise Gate or nothing, and I use it with lower settings then.

=== Open/Close Thresholds ===

The Hard Gate has two threshold levels - open and close. If the gate is currently open, it is only looking at the Close Threshold value to determine if it should close. If the gate is closed, it is only looking at Open Threshold to determine if it should open. This helps in two ways.

Single threshold gates are subject to jitter - consider a sustained note that is gradually decreasing in volume. The level you hear might be 96, 95, 95, 95, 95, 95, 94 db at 1/20th of a second intervals. The level the gate detects might be a little different, let's say 96, 95, 94, 95, 94, 95, 94. If the Threshold was set to 94.5 db, the gate would open and close rapidly as a decaying note hit the threshold value. It would sound like sputtering, which is very noticeable and undesirable.

With separate Open and Close Thresholds, you can set them a few db's apart, and the imprecision in the effect's signal level detection will not cause a sputtering gate.

This also comes in handy due to guitar naturally having a strong attack. Setting the Open Threshold high means when the gate is closed, you won't accidentally open it with soft noises you make when you're not trying to play a note, such as your fingers rubbing on unfretted strings. Yet, once you do purposefully play a note, the attack is strong enough to open the gate. Setting a single threshold gate to such a high threshold would mean that sustained decaying notes would get "cut off" rather than naturally fading to silence. With a low Close Threshold setting, however, you can let the note decay to almost silence before the gate closes.

While you can fake the above technique with a single threshold gate by turning up the Decay parameter, it's more favorable to set Decay lower and use two tresholds. It sounds better, and you'll get the expected gate behavior when you're playing quick staccato notes or sustaining notes.

=== Hold ===

The Hard Gate also features a Hold parameter that specifies a time to hold the gate open even after the Close Threshold has been passed. This can be used to reduce jitter as described in the last section, but as mentioned, staggered Open/Close Threshold settings should take care of that.

Where I find Hold is useful if you are using a longer Decay time. If you are playing a staccato part, the fade-out of the noise between notes is very noticeable, compared to if the noise were to remain at a constant level. Setting a hold time is basically taking a little time to make sure the gate should really be closing.

=== Decay ===

For a spacious lead tone, where any decay is going to be buried by reverb or delay, I like to turn Decay a bit off 0 such as 100-200ms - so there's not an obvious sound when the gate kicks on. For super tight rhythms, I like it at 0; but this means I have to be careful about my muting and exactly where I set the Threshold(s).

=== Placement in the Chain ===
See [[Effects Ordering/Position]].

=== Dialing it in ===

To dial in the Hard Gate, start with Hold and Decay set to 0 ms. Set both Open and Close Threshold around 9:00 (about -70db) - easily opened but still high enough to make the gate close when muting. If the gate won't close at these settings, turn them both up until the gate closes with the guitar muted, but with its volume knob at 10/10.

Then I see if I can make the gate open using a mundane noise, such as tapping a string, or rubbing a string with my finger. If so, I turn it up a bit. Once I've gotten it high enough so it won't open from any incidental noises and intermittent hum, I see if it will open by playing the softest note I intend to play. This varies from patch to patch. For a soft lead patch, this might be a mild hammer-on onto a silent string. For my Meshuggah rhythm patch, it's going to be a picked note at at least medium strength. If it won't open, I have to turn it down, even if this means it will also open from incidental noise as I play. Better for it to pick up some incidental noise than block out purposeful playing.

Then I back down the Close Threshold. I want to test it against punchy staccatto notes and chords as well as sustaining notes. I need it to activate between my stacatto playing but not kill a sustaining note; however, these are conflicting goals.

The "middle ground" I choose depends on the patch. For a soft lead, I want it low enough to sustain notes as long as possible. This means I have to make sure the guitar is completely muted to get the gate to close, so I have to pay more attention to doing so if I'm trying to play stacatto or after I let a note decay. For my Meshuggah patch, I want to make sure it activates as soon as I mute the guitar, even if my mute didn't have perfect technique. I'm not sustaining many notes for very long, especially single notes higher on the fretboard which are more sensitive to decay. So long as it doesn't cut off a sustained power chord after a few seconds, I'm happy.

I leave Hold at 0 ms. The Hard Gate is precise and quick enough so that I don't have to worry about trailing noise when quickly muting the guitar from a loud volume. Since I set Decay to a very low time, I don't need to worry about hearing a fade-out of noise either.

If I can get away with setting Decay to 0 ms, I'll do that, but if the gate kicking on creates an unnatural tone, I'm going to either need to use two gates, or introduce a little Decay. I set it just barely off 0, at like 20 ms. The slight decay prevents an unnatural cut-off sound, but it's not long enough so that you hear noise fade out after staccato notes. If it's not tight enough, we'll have to use two gates.

=== Dual Gates ===

Using two gates is useful when you're using strong compression or distortion, and you need to go from punchy chords to dead silence very quickly. I like to place the first gate as the first thing in the chain. I dial it in as described above, but it may not kick on fast enough, and those snippets of noise occurring as I'm muting are being amplified and are obvious when listening to the tone.

I add another gate after the compressor/distortion stage that is adding most of the compression. For many people, this is the end of the chain. For me, it's usually before the amp, but after a compressor or distortion effect with a little drive. I dial this one in exactly like the first one, and I turn the first one off while I'm doing so.

Once I've got them both tuned, I try the patch out with them both on. Sometimes it'll end up gating a little too much. I tend to back off the first gate a bit, while keeping the final gate firm.

{{top}}
{{Pod HD Guide Crumbs|4}}

[[Category:Guitar]]
[[Category:Gear]]
[[Category:Modelers]]
[[Category:Guides]]
[[Category:Pod HD]]